10 m超大采高工作面顶板回转与高位冲切结构模型及控制

Roof structure formed by large height-to-span rotating block and upper punching beam in longwall panel with ultra-large cutting height of 10 m and its control

  • 摘要: 为实现煤炭工业高质量发展目标,我国建成了一批8~10 m超大采高工作面。超大采高工作面一次采出空间成倍增加,采动影响范围大、扰动强,矿压显现剧烈,威胁生产安全。为提升超大采高工作面顶板控制效果,以曹家滩122104工作面为工程背景,采用理论分析、室内试验和现场实测手段研究超大采高工作面厚硬顶板运动规律,建立顶板结构模型,分析顶板失稳机理及支架阻力计算方法,揭示超大采高工作面强矿压产生机制,指导厚硬顶板压裂层位确定。结果表明:超大采高工作面多层厚硬顶板成组发生联动剪切破断,破断岩块回转速度快、幅度高,形成高跨比大于1的回转体;回转体支撑作用下高位厚硬岩组经历剪切破断、自由落体、旋转运动、冲切破断4个运动阶段,形成顶板回转体与高位冲切梁复合结构;揭示了厚硬顶板剪切破断机理,给出了顶板回转体保持平衡和厚硬岩组冲切破断的力学条件,提出了冲切力计算方法,厚硬岩组冲切破断是超大采高工作面多重动载的关键致因;考虑低位摩擦效应和高位冲切效应,构建了顶板回转及高位冲切复合作用下超大采高工作面支架阻力计算模型。厚硬顶板区域压裂卸压技术是减缓工作面强矿压的有效手段,基于顶板回转与冲切结构模型,得到了压裂岩层范围确定方法;压裂后厚硬顶板强度劣化,能量积聚程度降低,采动覆岩微震事件集中程度和释放能量减少,覆岩离层裂隙发育程度升高,厚硬顶板破断由剪切向拉伸模式转变,支架阻力降低幅度达到11.5%,研究成果可为厚硬顶板超大采高工作面支架选型和压裂参数确定提供指导。

     

    Abstract: To achieve high-quality development of the coal industry, a series of longwall panels with ultra-large cutting heights (8–10 m) have been developed in China. In such panels, mined-out space increases quickly. The mining influence range is large and mining disturbance is intense, resulting in severe strata behavior and threatening mining safety at the working face. For improving roof supporting effectiveness in such longwall panels, No.122104 longwall panel in Caojiatan Coal Mine is selected as the engineering case. Thick-hard strata movement characteristics, roof structure model, roof instability mechanism and support resistance determination method in longwall panel with ultra-large cutting height are analyzed with theoretical analysis, laboratory test and field measurement, helping to select the strata needing hydraulic fracturing. The results show that thick-hard strata undergo simultaneous shear rupture in longwall panels with ultra-large cutting heights. The fractured blocks exhibit large rotation angles due to the large cutting height, forming roof rotating blocks with large height-to-span ratios above the supports. The high-level thick-hard strata undergo shear rupture, free falling, rotational motion and punching rupture under the support of roof rotating blocks, forming a composite roof structure consisting of high-level punching beams and roof rotating blocks. Shear rupture mechanisms is revealed for the thick-hard strata. Mechanical conditions for the stability of rotating block and punching rupture of thick-hard strata are derived. Determination method for the punching force is proposed. The punching rupture of high-level roof strata is identified as a critical cause of multiple dynamic loads. Both lower frictional effect and high-level punching effect are considered, support force calculation model is established under the composite structure. Zonal hydraulic fracturing technique serves as an effective method for weakening the strong mining pressure. Identification principle is given for the fracturing level. The strata prone to punching rupture are identified as the targets for hydraulic fracturing. The fracturing range is also determined for the overburden strata based on the developed model. After fracturing, the strength of the thick-hard roof is weakened. Elastic strain energy stored in the roof is reduced. Thus, the number and energy of mining-induced micro-seismic events are dropped. The bedding separation fracture developed in the overburden is increased. The failure mode of fractured strata transits from shear to tension type. Support force decreases by 11.5%. The results may provide guidance for support selecting and regional hydraulic fracturing in longwall face with ultra-large cutting height and thick-hard strata.

     

/

返回文章
返回