ZHAO Tongbin,YIN Yanchun,REN Wentao,et al. Coal burst risk monitoring method based on the drilling powder of destressing drilling in coal seam and its application[J]. Journal of China Coal Society,2025,50(5):2384−2393. DOI: 10.13225/j.cnki.jccs.2024.0715
Citation: ZHAO Tongbin,YIN Yanchun,REN Wentao,et al. Coal burst risk monitoring method based on the drilling powder of destressing drilling in coal seam and its application[J]. Journal of China Coal Society,2025,50(5):2384−2393. DOI: 10.13225/j.cnki.jccs.2024.0715

Coal burst risk monitoring method based on the drilling powder of destressing drilling in coal seam and its application

More Information
  • Received Date: June 22, 2024
  • The drilling powder monitoring method is one commonly used method for coal burst risk evaluation in coal mines. The construction method of large-diameter destressing drilling is similar to that of the drilling powder monitoring method. However, due to the lack of drilling powder rate index and efficient weighing method, the drilling powder method based on destressing drilling has not been widely used. Therefore, based on the drilling powder rate index of standard drilling powder monitoring method, one method for determining the drilling powder rate index and the critical powder of large-diameter destressing drilling is proposed, in which its pressure relief effect is considered. By carrying out the laboratory tests of drilling in coal specimens, the functional relationship among the drilling diameter, powder, initial stress and stress after pressure relief is obtained. Then the suggested value of the drilling powder rate index and critical powder of 150mm diameter drilling with 1, 2 and 3 m spacing are obtained. Finally, by using the auto measuring device, the drilling powder of destressing drillings are measured in coal burst risk roadway. The results show that the drilling powder is positively correlated with the drilling diameter and coal stress. Meanwhile, the stress reduction rate after drilling is positively correlated with the drilling diameter-spacing ratio. The drilling powder rate index of 150 mm diameter destressing drilling is higher than that of 44 mm diameter drilling, and the index increases with the decrease of drilling spacing. The drilling powder of 150 mm diameter drilling in 6310 workingface of Tangkou Mine in Shandong is 25−93 kg/m, and there is high stress area at the depth of 12−14 m and 18−20 m from the coal wall. The drilling powder in the gob-side roadway is significantly heavier than that in the solid-coal roadway. Combing the drilling powder rate index determining method and the powder auto measuring device for large-diameter drilling, the coal burst risk monitoring method based on the drilling powder of destressing drilling is developed, which can provide one operative technical approach for the synchronous operation of pressure relief-monitoring in coal burst risk roadway.

  • [1]
    潘一山,宋义敏,刘军. 我国煤矿冲击地压防治的格局、变局和新局[J]. 岩石力学与工程学报,2023,42(9):2081−2095.

    PAN Yishan, SONG Yimin, LIU Jun. Pattern, change and new situation of coal mine rockburst prevention and control in China[J]. Chinese Journal of Rock Mechanics and Engineering,2023,42(9):2081−2095.
    [2]
    袁亮,王恩元,马衍坤,等. 我国煤岩动力灾害研究进展及面临的科技难题[J]. 煤炭学报,2023,48(5):1825−1845.

    YUAN Liang, WANG Enyuan, MA Yankun, et al. Research progress of coal and rock dynamic disasters and scientific and technological problems in China[J]. Journal of China Coal Society,2023,48(5):1825−1845.
    [3]
    DAI L P, PAN Y S, ZHANG C G, et al. New criterion of critical mining stress index for risk evaluation of roadway rockburst[J]. Rock Mechanics and Rock Engineering,2022,55(8):4783−4799. doi: 10.1007/s00603-022-02888-7
    [4]
    谭云亮,张修峰,肖自义,等. 冲击地压主控因素及孕灾机制[J]. 煤炭学报,2024,49(1):367−379.

    TAN Yunliang, ZHANG Xiufeng, XIAO Ziyi, et al. Main control factors of rock burst and its disaster evolution mechanism[J]. Journal of China Coal Society,2024,49(1):367−379.
    [5]
    张俊文,邓雪杰,郑通达. 充填开采防治坚硬顶板型冲击地压综述研究[J]. 绿色矿山,2024(2):103−121.

    ZHANG Junwen, DENG Xuejie, ZHENG Tongda. A review on hard roof rock burst prevention and control by backfill technology[J]. Journal of Green Mine,2024(2):103−121.
    [6]
    王国法,潘一山,赵善坤,等. 冲击地压煤层如何实现安全高效智能开采[J]. 煤炭科学技术,2024,52(1):1−14. doi: 10.12438/cst.2023-1656

    WANG Guofa, PAN Yishan, ZHAO Shankun, et al. How to realize safe-efficient-intelligent mining of rock burst coal seam[J]. Coal Science and Technology,2024,52(1):1−14. doi: 10.12438/cst.2023-1656
    [7]
    谭云亮,郭伟耀,辛恒奇,等. 煤矿深部开采冲击地压监测解危关键技术研究[J]. 煤炭学报,2019,44(1):160−172.

    TAN Yunliang, GUO Weiyao, XIN Hengqi, et al. Key technology of rock burst monitoring and control in deep coal mining[J]. Journal of China Coal Society,2019,44(1):160−172.
    [8]
    ZHENG Y H, ZHAO Z G, ZHAO T B, et al. A new method for monitoring coal stress while drilling process:Theoretical and experimental study[J]. Energy Sources, Part A:Recovery, Utilization, and Environmental Effects,2023,45(2):3980−3993. doi: 10.1080/15567036.2023.2200736
    [9]
    潘一山,肖永惠,罗浩,等. 冲击地压矿井安全性研究[J]. 煤炭学报,2023,48(5):1846−1860.

    PAN Yishan, XIAO Yonghui, LUO Hao, et al. Study on safety of rockburst mine[J]. Journal of China Coal Society,2023,48(5):1846−1860.
    [10]
    尹延春,郑武威,赵同彬,等. 煤层钻孔钻进煤粉自动测量方法及试验研究[J]. 煤炭科学技术,2023,51(11):23−32. doi: 10.12438/cst.2022-2006

    YIN Yanchun, ZHENG Wuwei, ZHAO Tongbin, et al. Automatic measurement method of drilling-cuttings of boreholes in the coal seam and test study[J]. Coal Science and Technology,2023,51(11):23−32. doi: 10.12438/cst.2022-2006
    [11]
    曲效成,姜福兴,于正兴,等. 基于当量钻屑法的冲击地压监测预警技术研究及应用[J]. 岩石力学与工程学报,2011,30(11):2346−2351.

    QU Xiaocheng, JIANG Fuxing, YU Zhengxing, et al. Rockburst monitoring and precaution technology based on equivalent drilling research and its applications[J]. Chinese Journal of Rock Mechanics and Engineering,2011,30(11):2346−2351.
    [12]
    唐巨鹏,陈帅,于宁. 基于平均有效应力煤与瓦斯突出钻屑量指标研究[J]. 地球物理学进展,2017,32(1):395−400. doi: 10.6038/pg20170156

    TANG Jupeng, CHEN Shuai, YU Ning. Study on the drilling cuttings bits index of coal and gas outburst based on average effective stress[J]. Progress in Geophysics,2017,32(1):395−400. doi: 10.6038/pg20170156
    [13]
    唐巨鹏,李卫军,潘一山,等. 钻杆直径及钻进速度对钻屑量影响试验研究[J]. 采矿与安全工程学报,2019,36(1):166−174.

    TANG Jupeng, LI Weijun, PAN Yishan, et al. Experimental study on the influence of drill pipe diameter and drilling velocity on drilling cuttings[J]. Journal of Mining & Safety Engineering,2019,36(1):166−174.
    [14]
    周洋,梁冰,孙维吉,等. 深部煤层钻屑粒度随钻进深度分布规律[J]. 中国安全生产科学技术,2020,16(1):66−72.

    ZHOU Yang, LIANG Bing, SUN Weiji, et al. Distribution laws of particle size of drilling cuttings with drilling depth in deep coal seams[J]. Journal of Safety Science and Technology,2020,16(1):66−72.
    [15]
    李京达,魏全德,贾明魁. 大直径钻孔钻屑检验方法及现场应用[J]. 煤矿安全,2016,47(1):126−129.

    LI Jingda, WEI Quande, JIA Mingkui. Method of large diameter drilling cuttings inspection and its application[J]. Safety in Coal Mines,2016,47(1):126−129.
    [16]
    顾广耀,王家玉. 大直径钻孔钻屑指标法临界值的研究[J]. 煤炭技术,2007,26(3):60−62.

    GU Guangyao, WANG Jiayu. Research on critical value of drilling index for bigger diameter borehole[J]. Coal Technology,2007,26(3):60−62.
    [17]
    GENG Y F, TAN J, YIN Y C, et al. Theoretical analysis of drilling cuttings considering stress zoning of surrounding rock and its application in stress detection[J]. Energy Science & Engineering,2023,11(5):1662−1670.
    [18]
    丁传宏,吴振华,潘鹏志,等. 不同地质条件下冲击地压特厚煤层钻屑法检测指标确立方法研究及应用[J]. 武汉理工大学学报,2018,40(9):52−58.

    DING Chuanhong, WU Zhenhua, PAN Pengzhi, et al. Research and application of determining evaluating index of rock burst in exceptionally thick coal with drilling cutting method under the different geological conditions[J]. Journal of Wuhan University of Technology,2018,40(9):52−58.
    [19]
    朱广安,刘欢,苏晓华,等. 基于声发射特征的含水煤体钻屑法临界指标优化试验研究[J]. 煤炭学报,2023,48(12):4433−4442.

    ZHU Guangan, LIU Huan, SU Xiaohua, et al. Experimental study on critical index optimization of drilling cuttings method of water-bearing coal based on acoustic emission features[J]. Journal of China Coal Society,2023,48(12):4433−4442.
    [20]
    朱广安,刘海洋,沈威,等. 富水条件下冲击煤体钻屑法试验研究[J]. 岩石力学与工程学报,2022,41(12):2417−2431.

    ZHU Guang’an, LIU Haiyang, SHEN Wei, et al. Experimental research on burst-prone coal mass of drilling method under rich water condition[J]. Chinese Journal of Rock Mechanics and Engineering,2022,41(12):2417−2431.
    [21]
    杜才溢,张玉江,孟鑫,等. 基于钻屑量界限方程的冲击危险性判定新方法[J]. 矿业安全与环保,2024,51(1):86−91.

    DU Caiyi, ZHANG Yujiang, MENG Xin, et al. A new method of rock burst hazard determination based on drilling cuttings limit equation[J]. Mining Safety & Environmental Protection,2024,51(1):86−91.
    [22]
    YIN Y C, CHEN B, ZHANG Y B, et al. Experimental study and evaluation on the weakening of bursting liability of coal with boreholes[J]. Engineering Failure Analysis,2024,155:107754. doi: 10.1016/j.engfailanal.2023.107754
    [23]
    谭云亮,郭伟耀,赵同彬,等. 深部煤巷帮部失稳诱冲机理及“卸−固” 协同控制研究[J]. 煤炭学报,2020,45(1):66−81.

    TAN Yunliang, GUO Weiyao, ZHAO Tongbin, et al. Coal rib burst mechanism in deep roadway and “stress relief-support reinforcement” synergetic control and prevention[J]. Journal of China Coal Society,2020,45(1):66−81.
    [24]
    张东晓,王翔宇,郭伟耀,等. 煤层厚度影响下大直径钻孔卸压释能机理[J]. 煤炭科学技术,2024,52(6):40−50. doi: 10.12438/cst.2023-0654

    ZHANG Dongxiao, WANG Xiangyu, GUO Weiyao, et al. The influence of coal seam thickness on the pressure relief and energy release mechanism of large-diameter drilling hole[J]. Coal Science and Technology,2024,52(6):40−50. doi: 10.12438/cst.2023-0654
    [25]
    赵志刚,张凯,尹延春,等. 不同应力下煤体钻孔试验及钻进能量响应研究[J]. 岩土力学,2023,44(10):2899−2906.

    ZHAO Zhigang, ZHANG Kai, YIN Yanchun, et al. Drilling test and drilling energy response of coal under different stresses[J]. Rock and Soil Mechanics,2023,44(10):2899−2906.
    [26]
    潘俊锋,闫耀东,马宏源,等. 一次成孔300 mm煤层大直径钻孔防冲效能试验[J]. 采矿与岩层控制工程学报,2022,4(5):5−15.

    PAN Junfeng, YAN Yaodong, MA Hongyuan, et al. Using 300 mm diameter boreholes for coal burst prevention a case study[J]. Journal of Mining and Strata Control Engineering,2022,4(5):5−15.
    [27]
    李云鹏,张宏伟,韩军,等. 基于分布式光纤传感技术的卸压钻孔时间效应研究[J]. 煤炭学报,2017,42(11):2834−2841.

    LI Yunpeng, ZHANG Hongwei, HAN Jun, et al. Time effect of borehole pressure relief based on distributed optical fiber sensing technology[J]. Journal of China Coal Society,2017,42(11):2834−2841.
    [28]
    苏超,康红普,姜鹏飞,等. 基于连续实测的煤巷围岩掘−采期间采动应力演化与破坏模式分析[J]. 岩石力学与工程学报,2024,43(9):2201−2213.

    SU Chao, KANG Hongpu, JIANG Pengfei, et al. Analysis on mining-induced stress evolution and surrounding rock failure mode of roadway during heading-mining period based on continuous measurement[J]. Chinese Journal of Rock Mechanics and Engineering,2024,43(9):2201−2213.
    [29]
    潘一山. 煤体钻粉理论的研究[J]. 阜新矿业学院学报,1985,4(S1):91−97.

    PAN Yishan. Study on the theory of coal body drilling powder[J]. Journal of Liaoning Technical University:Natural Science,1985,4(S1):91−97.
    [30]
    赵阳升,梁纯升,刘成丹. 钻屑法测量围岩压力的探索[J]. 岩土工程学报,1987,9(2):104−110. doi: 10.3321/j.issn:1000-4548.1987.02.013

    ZHAO Yangsheng, LIANG Chunsheng, LIU Chengdan. Exploration of measuring surrounding rock pressure by drilling cuttings method[J]. Chinese Journal of Geotechnical Engineering,1987,9(2):104−110. doi: 10.3321/j.issn:1000-4548.1987.02.013
    [31]
    LU X W, JIANG J Y, WANG W, et al. Laboratory experimental study on the pressure relief effect of boreholes in sandstone under high-stress conditions[J]. Sustainability,2023,15(21):15557. doi: 10.3390/su152115557
    [32]
    GONG F Q, HE Z C, SI X F. Experimental study on revealing the mechanism of rockburst prevention by drilling pressure relief:Status-of-the-art and prospects[J]. Geomatics, Natural Hazards and Risk,2022,13(1):2442−2470. doi: 10.1080/19475705.2022.2121227
    [33]
    ZHAO R J, YAO R B, ZHANG T, et al. Estimation of tunnel in situ stress magnitude and direction using measurement while drilling data and acoustic wave information[J]. Tunnelling and Underground Space Technology,2024,152:105905. doi: 10.1016/j.tust.2024.105905
    [34]
    吕祥锋,曹立厅,孟令峰,等. 旋压触探随钻摩阻表征围岩应力分布特征研究[J]. 岩石力学与工程学报,2023,42(10):2385−2399.

    LYU Xiangfeng, CAO Liting, MENG Lingfeng, et al. Surrounding rock stress distribution characterization via drilling friction resistance while rotary sounding[J]. Chinese Journal of Rock Mechanics and Engineering,2023,42(10):2385−2399.
    [35]
    ZHANG W L, LI C, JIN J X, et al. A new monitoring-while-drilling method of large diameter drilling in underground coal mine and their application[J]. Measurement,2021,173:108840. doi: 10.1016/j.measurement.2020.108840

Catalog

    Article views (125) PDF downloads (56) Cited by()

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return